loading force造句
例句與造句
- new intelligent combined testing system of loading force parameters
新型組合式加載力參數智能測試系統 - when the contact models are being built, an effective method is presented to solve the problem of bringing pre-load force
在建立接觸模型時，對預緊力的施加提出了有效可行的處理方法。 - third, the slope of the effective pote ntial corresponds to an average force . because of the existence of the average force, the motor protein can have a directed motion against the load force
只有當溫度達到某一值時，幾率流和有效勢的斜率才同時隨溫度的增加而減小，這時幾率流和有效勢傾斜的斜率密切相關。 - on the other hand, the wrist joints torque is tested when a load forced on the handle . the required torque is not beyond torque the engineer can afford, so that prove the analysis and calculation is correct
另一方面,通過測試施加負載后的手腕末端各關節的力矩大小,證明手腕所需要的力矩在實際電機和力傳感器的要求范圍內。 - in this dissertation, the development survey, research actualities and application prospect of vamt are introduced at first, and the models of kinematics, dynamics and linear motor servo are analyzed then . currently the dynamics model is complex or established mechanically, which restricts the study of control theories . thus this dissertation present a simple and easy-realized control idea, namely, the fore and torque of every leg determined by the inverse-solution of mechanics are regarded as changeable load force ( disturbance ) applied in motor, the elongation of the leg or displacement of sliding is regarded as the output of linear servo system
本文首先介紹了虛擬軸機床的發展概況、研究現狀和應用前景，然后對其運動學、動力學、直線伺服系統模型進行分析，針對目前動力學模型過于復雜或完全從機構學角度建立不便于控制的問題，提出了簡單、易于實現的控制思想，即將虛擬軸機床的動力學方程反解所確定的各桿受力(矩)視為電機的可變負載力，以桿長伸縮量或滑塊位移為伺服系統輸出，從此構成位置閉壞，實現軌跡跟蹤控制。 - It's difficult to find loading force in a sentence. 用loading force造句挺難的
- in the design of loading-frame, puting forword a group of universal dimensions of three-point free-link attachment to category i and ii tractors through comparing and analysing whose scope of dimensions, thereout, working out sketch of loading framework on several different positions in the whole lift-course of hydraulic liftenafter this . analysing the case of force on loading framework when the loading force equal to 44100n and the lift-position of the hydraulic lifter is on upper limit, and giving a data table about the case of force on all these positions, consequently, completing the design of loading frame
在加載框架的設計部分，通過對、類拖拉機的三點懸掛機構桿件尺寸范圍的比較分析，給出了一組、類拖拉機通用的三點懸掛機構桿件尺寸，由此作出了液壓提升器提升全行程中幾個不同位置的加載機構簡圖，并按44100n的加載力、以上極限位置為例對加載機構進行了受力分析，并給出了包括其它幾個位置在內的受力情況表，進而完成了加載框架的設計。